New panels
Fresh metal cut to length for each slope is fastened to the manufacturer pattern.
Metal Roofing
Metal Roof Replacement Butler, NJ
A roofer in Butler can replace a metal roof that has rusted through, lost its finish or been riddled with worn screw holes, down to the purlins or deck, after checking the framing and decking underneath. Call (862) 356-0005 to reach a local roofer.
Replacement comes up once rust or wear has spread past what patches and new fasteners can fix. When panels are perforated by rust, the finish is gone and every screw hole has been enlarged by years of movement, repairs stop keeping up. Thin panels from decades past are usually the first to rust through.
Not every metal roof replacement starts with a tear-off. A full tear-off removes the old panels and trim so the purlins or deck can be inspected and repaired, then new metal goes on. In a retrofit, new panels go over the old roof on a framing system, avoiding tear-off on large or occupied buildings.
Plenty of homeowners replace an old shingle roof with metal rather than more shingles. The shingles can come off or, if local code permits and the deck is sound, the metal can go over them. It helps to know what is on the roof now, how old it is and whether it has ever been covered over.
Depending on what the roofer finds, metal roof replacement in Butler, NJ can go hand in hand with metal roof installation and metal roof repair.
Need metal roof replacement in Butler? Call (862) 356-0005 and describe the problem to a roofer who works in Butler.
Call nowThe process
The metal roof replacement process
The order of work depends on tear-off or re-cover, but the basics are the same.
Check the framing
The roofer counts rust-through spots, checks the finish and inspects the purlins or decking from inside the attic or building. The findings shape the replacement plan.
Choose the approach
The roofer and owner pick the panel profile, metal and color and decide how the old roof will be handled. Switching to standing seam usually means adding solid decking.
Strip the panels
Panels and trim come off section by section and go to a metal recycler. The roof is never left open overnight.
Repair the framing
Framing and sheathing damaged by old leaks are replaced before new metal goes on. New screws in rotten wood would fail within a few seasons.
Panel the roof
High-temperature underlayment, new trim, panels, closures and flashing go on in order from the eaves up. Snow guards and ventilation are added where needed.
What is included
Parts of a metal reroof
Retrofit framing
New panels can be installed over existing metal with fasteners driven into the structure below.
Flashing
All new eave, rake, ridge and wall trim instead of reusing old pieces.
Old roof removal
The worn roof is stripped down to the framing section by section.
Framing repair
Damaged structure is repaired for a straight, solid roof.
Related service
Metal Roof Panel Replacement Butler, NJ
Panel replacement is the middle ground between a patch and a full metal roof replacement. The damaged panel is unscrewed, the laps on either side are freed and a new panel of the same profile is lapped in and fastened. Concealed fastener panels take more time to replace because of the seams.
On a Butler roof that is otherwise sound, a few new panels can add years of service. Expect a slight color difference between new and old metal. Once a large share of panels need work, replacement becomes the better plan.
Related service
Metal Roof Over Shingles Butler, NJ
Metal over shingles is a common way to switch to metal without stripping the old roof. Battens or a new underlayment layer go over the shingles, then the metal is fastened into the decking below.
The tradeoff is that nobody sees the deck. For Butler homes, the attic check is critical, since rotted decking will not hold fasteners. If the deck is questionable or there are already two layers, a tear-off is the better choice.
Local help
Metal Roof Replacement Near Me
In Butler, many metal replacements are older galvanized roofs that have finally rusted through. From Butler out to neighboring towns such as Riverdale, Bloomingdale, Pompton Plains and Pompton Lakes, older metal roofs tend to need full replacement once the coating is gone, and newer houses are adding metal as their shingle roofs wear out, so it pays to have the framing checked before deciding on a re-cover.
For metal roof replacement in Butler, NJ or nearby towns like Riverdale, Bloomingdale, Pompton Plains and Pompton Lakes, call (862) 356-0005 to reach a roofer who covers your street.
What the local climate does to a roof
Cold winters bring snow, ice and a long stretch of freezing nights. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, building ice dams that push water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. Most homeowners in Butler, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why fix it now
Less damage
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Familiar with local homes
Roofers in Butler know the roof types and weather wear common in local homes.
Clear next steps
Ask your questions before you agree to anything.
Common questions about metal roof replacement
Can a new metal roof go over the old metal roof?
In a retrofit, new panels go over the old roof on spacers or purlins. It is common on larger buildings where tearing off would disrupt use. The framing must be sound enough to support both layers.
How do I know my metal roof is past repair?
The tipping point comes when rust or wear is spread across the roof, not just in a few spots. If panels are perforated, the coating is gone and the fasteners no longer hold, patches will not keep up. A call to (862) 356-0005 is a good way to find out where the roof stands.
Is it a good idea to put metal over shingles?
Many codes allow metal over one layer of asphalt shingles. The upside is skipping tear-off, while the downside is not seeing the decking. A roofer can tell you which option fits your house.
What happens to the old metal roofing?
Old steel and aluminum panels are routinely taken to a scrap metal recycler. Metal can be melted down and reused, so it rarely goes to the landfill. Confirm how disposal is handled when you schedule.
Can I replace just one damaged metal panel?
One panel can usually be swapped without redoing the roof. The roofer unscrews the panel and its laps, removes it and fastens a matching one in place. Standing seam panels take more work because the seams must be opened.
More questions? Call (862) 356-0005
Related services
Metal Roof Installation
Choosing and installing a metal roof, from panel type and gauge to underlayment, trim and closures, for homes, garages and outbuildings.
Learn moreMetal Roof Repair
Replacing worn screws and washers, resealing panel laps, treating rust and fixing loose trim on metal roofs, matched to exposed fastener and standing seam roofs alike.
Learn moreRoof Replacement
A complete new roof from the deck up when repairs no longer make sense, so the house is dry for decades instead of seasons.
Learn moreStanding Seam Metal Roof
Standing seam metal roofs with concealed clips, raised seams and no exposed screws in the panels, for homes, additions and low slope roofs.
Learn more
Looking for something else?
See all roofing servicesTalk to a Butler roofer about metal roof replacement
Call now for Butler metal roof replacement and help in the towns around it.