Deck preparation
The base is cleared and checked so the roof sits on solid wood.
Flat Roofing
Rubber Roof Installation Butler, NJ
A Butler roofer who installs EPDM can put a new rubber roof on a flat or low slope section of almost any home, and explain each choice before the sheet is rolled out. One call to (862) 356-0005 reaches a nearby rubber roof installer.
EPDM is the material most people mean when they say rubber roof. It comes in large, flexible sheets, most often black, in 45 or 60 mil thickness, and its biggest strength is that it stays flexible in heat and cold without cracking. Unlike TPO and PVC, its seams are taped rather than heat welded.
Attachment method shapes the rest of the installation. The sheet can be glued to the substrate, fastened with plates at the seams or laid loose under a layer of stone. On most homes, fully adhered EPDM is the usual choice because it handles wind well and stays smooth.
Two more decisions round out the plan. Sixty mil EPDM costs a little more than 45 mil but resists punctures better and lasts longer. White EPDM suits sunny roofs, and black suits cooler climates. The transition to a steeper roof or a wall is planned with the same care, since that is where low roofs most often leak.
If the problem goes deeper than it first looked, a Butler roofer may also recommend rubber roof repair or flat roof installation.
Need rubber roof installation in Butler? Call (862) 356-0005 and describe the problem to a roofer who works in Butler.
Call nowThe process
The rubber roof installation process
Here is how a roofer typically installs an EPDM roof.
Prepare the deck
Damaged decking is replaced and drainage is confirmed before any insulation goes down. A tear-off comes first on existing roofs.
Insulation
Polyiso insulation and a cover board create a flat, firm base for the rubber. Tapered boards add slope where needed.
Roll out the membrane
The EPDM is unrolled, positioned and left to relax so wrinkles flatten before any adhesive goes on. Laps are arranged so water flows over them.
Apply adhesive
Half the sheet is folded back, adhesive is applied to both surfaces and the rubber is pressed into place. Then the other half is done the same way. Brooming from the middle outward pushes trapped air to the edges.
Tape the laps
Primer and seam tape join the sheets, with T-joints covered by extra patches. Lap sealant goes along exposed tape edges.
Finish the edges
Flashing goes up walls and around curbs, with boots at pipes and new edge metal at the perimeter. The top edge is sealed and covered. A final walk checks every seam with a probe before the job is closed out.
What is included
What goes into a rubber roof
Seam tape
Laps are joined with seam tape with lap sealant at the edges.
Rubber sheet
A 45 or 60 mil EPDM sheet is installed with as few seams as possible.
Insulation
Rigid insulation and a cover board form the base under the rubber.
Flashing
Walls, curbs, pipes and edges are flashed to keep water out.
Related service
EPDM Roof Installation Butler, NJ
The quality of an EPDM installation shows up years later in the seams and edges. Rushing the adhesive, skipping primer or leaving wrinkles under the sheet are the common mistakes. Installers work in dry weather so the bond holds. Different adhesives may be used in the field and at the flashings, each matched to the job it does.
In Butler, an experienced EPDM installer leaves room for the membrane to move and age. Securing the membrane at the edges and flashing corners correctly prevents later tears. Ask how the roofer secures the perimeter.
Local help
Rubber Roof Installation Near Me
Rubber roofs in Butler are common on porches, garages, additions and flat sections of older homes. Homes in Butler and nearby places including Riverdale, Bloomingdale, Pompton Plains and Pompton Lakes benefit from rubber roofing because it flexes with the seasons, which is why the seams and flashing deserve careful attention.
For rubber roof installation in Butler, NJ or nearby towns like Riverdale, Bloomingdale, Pompton Plains and Pompton Lakes, call (862) 356-0005 to reach a roofer who covers your street.
Roofs in this climate
Cold winters bring snow, ice and a long stretch of freezing nights. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, which is how ice dams form and back water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. That is why roof repair in Butler is busiest after a hard winter and before the next one.
Why call
Why not wait
Smaller repairs
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Roofers who know Butler
Local roofers see the same roofs and storm damage across Butler and nearby towns.
Know what happens next
Ask the roofer about the cause, the options and the estimate before work starts.
Common questions about rubber roof installation
Can a rubber roof go over an existing roof?
Recovering depends on the condition of the old roof. The old roof must be a single dry layer, with a recover board over it. Otherwise, a tear-off is needed. Core samples or a moisture scan show whether the old roof is dry enough.
What is the lifespan of a new EPDM roof?
EPDM can last 25 years or longer. Thickness, seam quality and maintenance all affect its life. Small repairs are easy to make.
Should my rubber roof be black or white?
The choice depends on the climate and the space below. White helps in sunny climates, and black is common where winters are long. A roofer can recommend what fits your home.
Is a rubber roof the same as TPO?
They are related but not the same. Black EPDM is taped and stretchy, and white TPO is welded and reflective. A roofer can help you choose.
How thick should a rubber roof be?
EPDM usually comes in 45 or 60 mil for homes. Sixty mil resists punctures better and lasts longer, which helps on roofs with foot traffic or hail. Even thicker sheets are available for demanding roofs.
More questions? Call (862) 356-0005
Related services
Rubber Roof Repair
EPDM rubber roof repairs done with primer, cover tape and lap sealant made for rubber, after the real leak point is found.
Learn moreFlat Roof Installation
New flat roofs built with real slope, insulation, a cover board and a membrane suited to the building, planned around how the roof will be used.
Learn moreTPO Roofing
TPO membrane roofs installed over new insulation or in place of a worn flat roof, with seams welded into one watertight sheet.
Learn moreFlat Roof Replacement
Tearing off or recovering a worn flat roof and installing a new membrane, insulation and edge metal, so ponding and repeat leaks end for good.
Learn more
Looking for something else?
See all roofing servicesNeed rubber roof installation in Butler, NJ?
Call (862) 356-0005 to talk to a roofer serving Butler, NJ.